regressing

英 [rɪˈɡresɪŋ]

美 [rɪˈɡresɪŋ]

v.  倒退; 回归; 退化
regress的现在分词

现在分词：regressing　

柯林斯词典

• VERB 倒退;退步;退化
  When people or thingsregress, they return to an earlier and less advanced stage of development.
  1. ...if your child regresses to babyish behaviour...
     如果你的孩子退行到婴儿状态
  2. Such countries are not 'developing' at all, but regressing.
     这些国家根本不是在“发展中”，而是在倒退。

双语例句

• According to the condition of predicting and research on present building fire in cities, the modeling theories and characters of exponential regressing model and ameliorated GM ( 1,1) model and wavelet neural network model are synthetically analyzed in this paper.
  针对目前城市建筑火灾预测研究的情况，综合分析了改进后的GM（1,1）模型和小波神经网络模型的建模理论和特点。
• Such countries are not 'developing' at all, but regressing.
  这些国家根本不是在“发展中”，而是在倒退。
• If you make tuning adjustments later, the baseline tells you whether you're making progress or regressing after the changes.
  如果以后进行优化调整，此基线将告诉您更改之后是有所改善还是有所退化？
• He's regressing to a psychopathic frenzy?
  他是在倒退成为精神性狂暴症吗？
• The least-squares estimation method measures economic exposure by regressing the firm's value and the exchange rates.
  本文仍然由易到难，首先估计了公司所面临的单个货币的外汇经济风险暴露；
• Unless you are the dominant low-cost operator, this can mean a profitless existence for many organisations keeping in line with competitors, but regressing overall.
  除非你是一个占统治地位的低成本运营商，否则这种情况就可能意味着许多机构以无利润的状况存在与竞争对手比肩而行，但全都是在后退。
• Based on regressing the curves of average relative permeability in single well, that the oil saturation distribution, permeability ( K) and average formation pressure have been gotten through seeking numerical solution to this two equations.
  在回归出单井平均相对渗透率曲线的基础上，通过求两个偏微分方程的数值解，求出了径向上的含油饱和度分布、地层渗透率K和平均地层压力；
• By comparing the payment pattern that collected by the revenue with that of regressing to the insurance agency; the social security system was put forward, which is a necessary option for the latter.
  通过对地税代征和回归社保两条路径选择的比较分析，提出“五险合一、回归社保”是建立一个以社保基金为依托的社会保障制度的必然选择。
• Furthermore, On the base determining dangerous section of rupture, relationship between rupture limit load of conical parts and rupture limit load of cylindrical parts is presented by means of theoretical analysis and regressing test data.
  而且，在确定了破裂危险断面的基础上，通过理论分析和实验数据回归，给出了圆锥形件成形的破裂极限载荷与圆筒形件拉深的破裂极限载荷之间的关系。
• The fitting curve and the function expression between the prestress and magnetostriction under the maximum current is achieved with the method of curve fitting and linear regressing, and the optimal working prestress is confirmed.
  利用最小二乘曲线拟合、线性回归等数学方法得出了刀架在最大工作电流下，预压力与磁致伸缩量之间的拟合曲线及函数多项式，并确立了最佳工作预压力。